LIAN LI LANCOOL II MESH RGB White 3x120mm Fan
Mesh intakes spanning the front panel guarantee sufficient airflow in and out of the system, allowing it to run at peak performance.
The optimized airflow is a result of the collaboration between the brand-new mesh design, additional exhaust vent holes, and three high-performance ARGB cooling fans.
3 x 120mm ARGB intake fans pre-installed at the front produce ample airflow while still offering bountiful RGB to liven up your PC build.
The fan power plug connecting to the 3 included fans is compatible with these two fan headers on the motherboard:
(splitter cable is not included)
Add the BORA DIGITAL ARGB FANs to have more vibrant RGB and increased cooling efficiency for your LANCOOL II MESH build!
To further control the added BORA DIGITAL FANs through the C and M buttons, connect the header to one of the headers on the cable connecting to the 3 included fans.
SHOP NOW
Lighting effects of the 3 included ARGB fans can be fully controlled through the C button and M button located on the top front. Switching between 8 lighting modes has never been this easy.
Note!
By plugging the fan hub’s ARGB header into the motherboard’s 3-PIN 5V addressable RGB headers, you’ll be able to synchronise the lighting effects with the motherboard software by switching the M button to the 8th mode.
Note!
If your motherboard doesn’t have any 5V addressable RGB headers, make sure to connect the SATA cable connecting the hub to the the power supply and use the C and M buttons to control the lighting effects.
The space between the top and bottom chamber now features two removable PSU shroud covers for either 2 x 2.5” SSDs or can be removed to fit 2 x 120mm fans.
Compared to the former integrated design, the modular PSU shroud covers allow users to remove them for an unobstructed airflow between the top and bottom chamber.
When 2 fans are mounted, and the cover plates removed, ventilation efficiency is even better.
Even when 2 x SSDs are mounted, the vents on the PSU shroud covers guarantee good ventilation.
The multi-way bracket revolutionizes your notion of fan/radiator installation by offering 4 installation options to best fit your needs.
The multi-way bracket revolutionizes your notion of fan/radiator installation by offering 4 installation options to best fit your need.
ATTENTION!
Do not install a 140/280MM radiator in the inner side of the bracket otherwise irreparable deformation might occur. The correct way to install is to mount fans first then place a radiator on top of the fans.
With the modular drive cage, side-mounted SSD bays, and additional SSD space on the modular PSU shroud cover, the LANCOOL II MESH is capable of holding up to 9 drives.
TOOLLESS SLIDING DRIVE CAGE
Slide the hard drive cage along its bottom track to the position that best fits your interior configuration.
SUPPORT UP TO 9 DRIVES
Modular drive cage: 3 x 3.5” HDDs/2.5” SSDs
Side-mounted SSD bays behind motherboard tray:
2 x 2.5” SSDs
Side-mounted SSD bays at the bottom right flip shroud:
2 x 2.5” SSDs
Flippable, flexible, multi-functional
The tempered glass side panels offer an unobstructed view to the interior configuration while the bottom shroud panels provide quick access to PSU/drive installation.
The cover plates save users’ neck and fingers by concealing nearly all the wayward cables.
Underneath the top right cover plate is a mounting plate for a removable fan/LED hub.
Model | LANCOOL II MESH RGB |
---|---|
Dimensions | (D) 478mm x (W) 229mm x (H) 494mm |
Motherboard | E-ATX(width: under 280mm)/ATX/M-ATX/ITX |
PSU | 210mm |
Color | black/white |
Materials | 0.8mm SGCC (exterior, MB tray, and most of the interior) 4.0mm tempered glass (both sides) 1.0mm SGCC (interior) |
Fan Support | Front (multi-way fan/radiator bracket): 3 x 120mm or 2 x 140mm Top: 2 x 120/140mm Rear: 1 x 120mm Above PSU Chamber: 2 x 120mm |
Radiator | Front (multi-way fan/radiator bracket): 1 x 360/280/240mm Top: 1 x 240mm (aligned to the left) |
VGA Length | 384mm |
CPU Clearance | 176mm |
Drive | Behind MB Tray: 2 x 2.5″ SSD Behind the right flip panel: 2 x 2.5”SSD Hard Drive Cage: 3 x 3.5″ HDD/2.5″ SSD Above PSU Chamber: 2 x 2.5″ SSD |
Slot | 7 |
I/O Ports | C button for color control M button for lighting mode control 1 x TRRS AUDIO 2 x USB 3.0 1 x USB 3.1 TYPEC (Optional) |
Dust Filters | 1 x Top (magnetic), 1 x Bottom (tray) |
Incl Fans | 3 x included 120mm 3-PIN 1300 RPM ARGB fans Rated Speed:1300RPM ±10 % Air Flow:49.14CFM Noise:25.0dB(A) |
Mesh intakes spanning the front panel guarantee sufficient airflow in and out of the system, allowing it to run at peak performance.
The optimized airflow is a result of the collaboration between the brand-new mesh design, additional exhaust vent holes, and three high-performance ARGB cooling fans.
3 x 120mm ARGB intake fans pre-installed at the front produce ample airflow while still offering bountiful RGB to liven up your PC build.
The fan power plug connecting to the 3 included fans is compatible with these two fan headers on the motherboard:
(splitter cable is not included)
Add the BORA DIGITAL ARGB FANs to have more vibrant RGB and increased cooling efficiency for your LANCOOL II MESH build!
To further control the added BORA DIGITAL FANs through the C and M buttons, connect the header to one of the headers on the cable connecting to the 3 included fans.
SHOP NOW
Lighting effects of the 3 included ARGB fans can be fully controlled through the C button and M button located on the top front. Switching between 8 lighting modes has never been this easy.
Note!
By plugging the fan hub’s ARGB header into the motherboard’s 3-PIN 5V addressable RGB headers, you’ll be able to synchronise the lighting effects with the motherboard software by switching the M button to the 8th mode.
Note!
If your motherboard doesn’t have any 5V addressable RGB headers, make sure to connect the SATA cable connecting the hub to the the power supply and use the C and M buttons to control the lighting effects.
The space between the top and bottom chamber now features two removable PSU shroud covers for either 2 x 2.5” SSDs or can be removed to fit 2 x 120mm fans.
Compared to the former integrated design, the modular PSU shroud covers allow users to remove them for an unobstructed airflow between the top and bottom chamber.
When 2 fans are mounted, and the cover plates removed, ventilation efficiency is even better.
Even when 2 x SSDs are mounted, the vents on the PSU shroud covers guarantee good ventilation.
The multi-way bracket revolutionizes your notion of fan/radiator installation by offering 4 installation options to best fit your needs.
The multi-way bracket revolutionizes your notion of fan/radiator installation by offering 4 installation options to best fit your need.
ATTENTION!
Do not install a 140/280MM radiator in the inner side of the bracket otherwise irreparable deformation might occur. The correct way to install is to mount fans first then place a radiator on top of the fans.
With the modular drive cage, side-mounted SSD bays, and additional SSD space on the modular PSU shroud cover, the LANCOOL II MESH is capable of holding up to 9 drives.
TOOLLESS SLIDING DRIVE CAGE
Slide the hard drive cage along its bottom track to the position that best fits your interior configuration.
SUPPORT UP TO 9 DRIVES
Modular drive cage: 3 x 3.5” HDDs/2.5” SSDs
Side-mounted SSD bays behind motherboard tray:
2 x 2.5” SSDs
Side-mounted SSD bays at the bottom right flip shroud:
2 x 2.5” SSDs
Flippable, flexible, multi-functional
The tempered glass side panels offer an unobstructed view to the interior configuration while the bottom shroud panels provide quick access to PSU/drive installation.
The cover plates save users’ neck and fingers by concealing nearly all the wayward cables.
Underneath the top right cover plate is a mounting plate for a removable fan/LED hub.
Model | LANCOOL II MESH RGB |
---|---|
Dimensions | (D) 478mm x (W) 229mm x (H) 494mm |
Motherboard | E-ATX(width: under 280mm)/ATX/M-ATX/ITX |
PSU | 210mm |
Color | black/white |
Materials | 0.8mm SGCC (exterior, MB tray, and most of the interior) 4.0mm tempered glass (both sides) 1.0mm SGCC (interior) |
Fan Support | Front (multi-way fan/radiator bracket): 3 x 120mm or 2 x 140mm Top: 2 x 120/140mm Rear: 1 x 120mm Above PSU Chamber: 2 x 120mm |
Radiator | Front (multi-way fan/radiator bracket): 1 x 360/280/240mm Top: 1 x 240mm (aligned to the left) |
VGA Length | 384mm |
CPU Clearance | 176mm |
Drive | Behind MB Tray: 2 x 2.5″ SSD Behind the right flip panel: 2 x 2.5”SSD Hard Drive Cage: 3 x 3.5″ HDD/2.5″ SSD Above PSU Chamber: 2 x 2.5″ SSD |
Slot | 7 |
I/O Ports | C button for color control M button for lighting mode control 1 x TRRS AUDIO 2 x USB 3.0 1 x USB 3.1 TYPEC (Optional) |
Dust Filters | 1 x Top (magnetic), 1 x Bottom (tray) |
Incl Fans | 3 x included 120mm 3-PIN 1300 RPM ARGB fans Rated Speed:1300RPM ±10 % Air Flow:49.14CFM Noise:25.0dB(A) |